OBJECTIVE TESTS ON D.C. GENERATORS.

By -

OBJECTIVE TESTS

1. The basic requirement of a d.c. armature wind- ing is that it must be

(a) a closed one

(b) a lap winding

(c) a wave winding

(d) either (b) or (c)

2. A wave winding must go at least ............ around the armature before it closes back where it started.

(a) once

(b) twice

(c) thrice

(d) four times

3. The d.c. armature winding in which coil sides are a pole pitch apart is called ............ winding.

(a) multiplex

(b) fractional-pitch

(c) full-pitch

(d) pole-pitch

4. For making coil span equal to a pole pitch in the armature winding of a d.c. generator, the back pitch of the winding must equal the number of

(a) commutator bars per pole

(b) winding elements

(c) armature conductors per path

(d) armature parallel paths.

5. The primary reason for making the coil span of a d.c. armature winding equal to a pole pitch is to

(a) obtain a coil span of 180º (electrical)

(b) ensure the addition of e.m.fs. of consecu- tive turns

(c) distribute the winding uniformly under different poles

(d) obtain a full-pitch winding.

6. In a 4-pole, 35 slot d.c. armature, 180 electrical-degree coil span will be obtained when coils occupy ............ slots.

(a) 1 and 10

(b) 1 and 9

(c) 2 and 11

(d) 3 and 12

7. The armature of a d.c. generator has a 2-layer lap-winding housed in 72 slots with six con- ductors/slot. What is the minimum number of commutator bars required for the armature?

(a) 72

(b) 432

(c) 216

(d) 36

8. The sole purpose of a commutator in a d.c.

Generator is to

(a) increase output voltage

(b) reduce sparking at brushes

(c) provide smoother output

(d) convert the induced a.c. into d.c.

9. For a 4-pole, 2-layer, d.c., lap-winding with 20 slots and one conductor per layer, the num- ber of commutator bars is

(a) 80

(b) 20

(c) 40

(d) 160

10. A 4-pole, 12-slot lap-wound d.c. armature has two coil-sides/slot. Assuming single turn coils and progressive winding, the back pitch would be

(a) 5

(b) 7

(c) 3

(d) 6

11. If in the case of a certain d.c. armature, the number of commutator segments is found ei- ther one less or more than the number of slots, the armature must be having a simplex ............ winding.

(a) wave

(b) lap

(c) frog leg

(d) multielement

12. Lap winding is suitable for ............ current,

............ voltage d.c. generators.

(a) high, low

(b) low, high

(c) low, low

(d) high, high

13. The series field of a short-shunt d.c. genera- tor is excited by ............ currents.

(a) shunt

(b) armature

(c) load

(d) external

14. In a d.c. generator, the generated e.m.f. is directly proportional to the

(a) field current

(b) pole flux

(c) number of armature parallel paths

(d) number of dummy coils

15. In a 12-pole triplex lap-wound d.c. armature, each conductor can carry a current of 100 A. The rated current of this armature is ............ ampere.

(a) 600

(b) 1200

(c) 2400

(d) 3600

16. The commercial efficiency of a shunt generator is maximum when its variable loss equals ............ loss.

(a) constant

(b) stray

(c) iron

(d) friction and windage

17. In small d.c. machines, armature slots are sometimes not made axial but are skewed. Though skewing makes winding a little more difficult, yet it results in

(a) quieter operation

(b) slight decrease in losses

(c) saving of copper

(d) both (a) and (b)

18. The critical resistance of the d.c. generator is the resistance of

(a) armature

(b) field

(c) load

(d) brushes (Grad. I.E.T.E Dec. 1985)

image

Comments

Post a Comment

Popular posts from this blog

Total Loss in a D.C. Generator

By -
Image
Total Loss in a D.C. Generator The various losses occurring in a generator can be sub-divided as follows : where R a = resistance of armature and interpoles and series field winding etc. This loss is about 30 to 40% of full-load losses. Field copper loss. In the case of shunt generators, it is practically constant and I 2 R (or V I sh ). In the case of series generator, it is = I s e 2 R s e where R s e is resistance of the series field winding. This loss is about 20 to 30% of F.L. losses. (iii) The loss due to brush contact resistance. It is usually included in the armature copper loss. (b) Magnetic Losses (also known as iron or core losses), (i) hysteresis loss, W h µ B max f and ( ii ) eddy current loss, W e µ B max f These losses are practically constant for shunt and compound-wound generators, because in their case, field current is approximately constant. Both these losses total up to about 20 to 30% of F.L. losses. (c) Mechanica l Losses. These consist of :...
Read more

Transformer,three phase:Wye/Delta or Y/∆ Connection and Delta/Wye or ∆/Y Connection.

By -
Image
Wye/Delta or Y/∆  Connection The main use of this connection is at the substation end of the transmission line where the voltage is to be stepped down. The primary winding is Y -connected with grounded neutral as shown in Fig. 33.6. The ratio between the secondary and primary line voltage is 1/ 3 times the transformation ratio of each trans- former. There is a 30° shift between the primary and secondary line voltages which means that a Y - D transformer bank cannot be paralleled with either a Y - Y or a D - D bank. Also, third harmonic currents flows in the D to provide a sinusoidal flux. Delta/Wye or ∆/Y Connection This connection is generally employed where it is necessary to step up the voltage as for example, at the beginning of high tension transmission system. The connection is shown in Fig. 33.7. The neutral of the secondary is grounded for providing 3-phase 4-wire service. In recent years, this connection has gained considerable popularity because it can be used to s...
Read more

Testing of d.c.Machines:Brake Test

By -
Image
Brake Test It is a direct method and consists of applying a brake to a water-cooled pulley mounted on the motor shaft as shown in Fig. 31.1. The brake band is fixed with the help of wooden blocks gripping the pulley. One end of the band is fixed to earth via a spring balance S and the other is connected to a suspended weight W 1. The motor is running and the load on the motor is adjusted till it carries its full load current. The simple brake test described above can be used for small motors only, because in the case of large motors, it is difficult to dissipate the large amount of heat generated at the brake. Another simple method of measuring motor output is by the use of poney brake one form of which is shown in Fig. 31.2 ( a ). A rope is wound round the pulley and its two ends are attached to two spring balances S 1 and S 2. The tension of the rope can be adjusted with the help of swivels. Obviously, the force acting tangentially on the pulley is equal to the differ ence ...
Read more